Bio-Tek Solvent's, Inc. ☎ 775-887-3554

Bio-Tek Solvent's, Inc.

Column

680 W. Nye Lane, Ste. 201 - Carson City, NV 89703-1500

Column

Email: info@bioteksolvents.com

Phone: 775-887-3554
Fax: 775-883-2384

134 HI-SOLV TECHNICAL DATA

Column

NSN6850-01-277-0595 / 5-GAL CAN

HI-SOLV is a solvent degreaser where confined atmospheric conditions require a cleaner that helps meet the federal government’s directive for reduction of hazardous materials or where EPA air pollution restrictions necessitate solvents with low vapor pressure. It is considered a safe replacement for PD-680 (dry cleaning solvent, Stoddard solvent) with a high flash point. Its non-conductive and controlled evaporation properties make it an ideal replacement for the more volatile solvents (including chlorinated and fluorocarbon materials) previously used.

HI-SOLV has been found to last approximately 4 times longer than PD-680, when used in parts wash cleaning tanks, making it cost-effective, and adds to the savings by reducing hazardous waste disposal.

Column

NSN6850-01-244-3207 / 55-GAL DRUM

This is accomplished because of the high purity and low volatility of the components used in its formulation.

Because of its purity, HI-SOLV is much less aggressive to the skin, substantially reducing the risk of dermatitis.

In an Air Force study, HI-SOLV was determined in laboratory tests to be biodegradable when handled in industrial wastewater treatment plants. This study was done by EG&G IDAHO TINKER AFB. OKLA. and was sponsored by AIR FORCE ENGINEERING & SERVICES CTR, TYNDALL AFB, FL. REPORT #ESL-TR-89-04 (PH. 904-283-2942).

Non-regulated material does not require flammable storage.

MSDS on file with HMIS, Richmond, VA. (804) 279-4371

General Uses:

Column

Electrical motors and equipment: Brush or spray until surface is covered, allow a few seconds to penetrate and re-spray to flush off. Di-electric strength permits cleaning of motors and equipment without shutting off your power (except arcing or DC equipment).
Machinery and production parts: Dip, brush, or spray, allow time for penetration and spray with HI-SOLV to flush off. Since HI-SOLV is consumed in the cleaning process, no makeup, analysis, or additions are required.

Column

Hydraulic systems: Flush through system to remove contaminated oils, follow with blow drying or allow enough time to air dry.
Food service: It may be used under FDA guidelines as a cleaner and diluent for lubricants used in ovens and other food service equipment. It will not leave any odor that may contaminate food.
Gunnery equipment: Because of confined spaces in which PMS is performed, HI-SOLV is an ideal cleaner for these areas. Its low residual after drying help reduce the oily film that attracts dust and other contaminants.

Physical Properties:

Type: Solvent degreaser	Vapor Pressure: <0.1 mmHg @ 20 deg. C
Color: Clear	Di-Electric Strength: Over 32,000 volts
Odor: Odorless	Non-Volatile Residue: Less than 100 PPM
Flammability: Flashpoint (PM) 210deg. F	Composition: Complex blend of petroleum hydrocarbons
Toxicity TLV: Over 500 PPM	VOC: 787 g/l

Special Benefits:

Biodegradable	Low End Use Cost
Excellent Degreaser	Reduces Hazardous Disposal
Controlled Evaporation State	Odorless
Safe on Metals and Plastics	Exceed FED. Spec. PD-680 Type II & III

Column

Specific Requirements/Authorizations:

P-250, MOD II Pumps, HI-SOLV is required for PMS by NAVSEA, POC Mark Hampson (215) 897-1257 PMS CARDS: S-24/A7SN, S-27/A7SR, A-40/B12J, LU-1/B12K, SU-12/A7TM.
Inflatable life preservers, required for use aboard ship for cleaning and degreasing prior to repairing leaks or adding components, see DTRC Report 2843: RAN, 10470, TM-28-88-10, NAVSEA POC Jim Hyslip (410) 293-2541, PMS CARDS: 993RLPN, 993YCXN.
Rast systems, authorized by Naval Air Engineering CTR. (NAEC) LAKEHURST, N.J. for PMS aboard ship. POC Gene Levchenko, (201) 323-7357 AV: 624-7357.
Authorized for use aboard ship by Naval Environmental Health CTR (NEHC), LTR.6263 SER 422FB/04369, DTD.27 APR.87. POC J.D. Drewyer. Head, Hazardous Materials Information BCH.PH (804)444-2699, AV: 564-4657.
IMA’S, Including AD, AR, and AS’s for use in engine shops by NAVSEA CODES 56X15 AND 05M ON MEMO 8806029 DTD; 2 JUNE 88. POC John Revnell PH: (703) 602-3271, AV: 222-3261.
Required for use aboard submarines for cold electrical cleaning, per NAVSEA S-9510-AB-ATM-010/ (U) and NAVENVIRHLTHCEN LTR 8282 SER 34DM/10030 OF 2 OCT 90. POC Mary Jo Bieberich, (410) 293-2758.
Use in lube and fuel oil analysis testing ship and shore. POC Mr. Joe Zerby, NAVSES, PHILA. (215)897-7496.
Ships hazardous material list (SHML) authorizes HI-SOLV to be used in place of PD-680. POC NSPCC, Mr. Dan Sieger, (717)790-6990.